Understand the evidence
Usable power-station capacity: what published tests actually tell us
Use measured energy from a similar load when it is available. Keep the test conditions attached to the number: a result at 1,000 W is not a reliable prediction for a router using 18 W.
A small evidence ledger
These measurements come from independent reviewers, not our own lab. They are deliberately shown separately. We do not average different loads, treat another region’s sockets as UK hardware, or turn a single result into a universal efficiency score.
| Station | Delivered energy | Conditions and source |
|---|---|---|
| Anker C1000 Gen 2 | 890 Wh | Reported US result; the source mixes Anker specifications, so model identification is uncertain. OutdoorGearLab: shared US tests |
| BLUETTI Elite 100 V2 | 890 Wh | Reported in that US comparison; not evidence of an efficiency tie with the UK Anker. OutdoorGearLab: shared US tests |
| Anker C1000 Gen 2 | 907 Wh | UK unit; 1,000 W heater load. The Technology Man: UK C1000 Gen 2 test |
| BLUETTI Elite 100 V2 | 936 Wh | European unit; 200 W load. Smartzone: European Elite 100 V2 test |
| BLUETTI Elite 100 V2 | 903 Wh | European unit; 1,800 W load. Smartzone: European Elite 100 V2 test |
| Anker C2000 Gen 2 | Just over 1,600 Wh | European unit; roughly 200 W. Notebookcheck: European C2000 Gen 2 test |
| Anker C2000 Gen 2 | About 1,850 Wh | Same review; 1,800 W. Notebookcheck: European C2000 Gen 2 test |
| DJI Power 1000 V2 | 880 Wh | Reported US table entry only. Its prose and table disagree on output/generation; exact-model measurement is unverified. OutdoorGearLab test |
| EcoFlow RIVER 3 Plus | No verified usable-energy result in our evidence set | Manufacturer-rated storage: 286 Wh. This is not delivered AC energy. Manufacturer source |
| Anker SOLIX C300X | No verified usable-energy result in our evidence set | Manufacturer-rated storage: 288 Wh. This is not delivered AC energy. Manufacturer source |
| BLUETTI Elite 200 V2 | No verified usable-energy result in our evidence set | Manufacturer-rated storage: 2,073.6 Wh. This is not delivered AC energy. Manufacturer source |
| EcoFlow DELTA 3 Max Plus | No verified usable-energy result in our evidence set | Manufacturer-rated storage: 2,048 Wh. This is not delivered AC energy. Manufacturer source |
| Jackery Explorer 2000 Plus v2 | No verified usable-energy result in our evidence set | Manufacturer-rated storage: 2,048 Wh. This is not delivered AC energy. Manufacturer source |
What we can reasonably conclude
OutdoorGearLab’s Anker table and prose disagree on output and sockets. We retain its reported numbers for traceability, but do not use them to rank efficiency or claim a tie. The UK and European tests below identify their loads more clearly. The separate UK and European measurements add context, but they do not prove one model is always more efficient. Our 1 kWh buying comparison also considers sockets, charging and the intended equipment.
The two C2000 readings illustrate why load matters. A fixed amount of power used by the station takes a larger share of the battery during a long, low-power discharge. A higher load may therefore extract more energy at the sockets while still exhausting the battery sooner in hours. There is no contradiction.
Use the right denominator
Rated capacity describes energy stored in the battery. Usable AC energy is what a particular test delivered at the mains sockets. Round-trip efficiency compares energy delivered with energy bought to recharge the station under a defined cycle. These quantities should not share one unqualified “efficiency” percentage.
If a test already measured 900 Wh delivered to its appliance, do not multiply that by 85% again before calculating runtime at the same load. Those conversion losses have already happened. If you instead start from rated capacity, you need assumptions about losses and overhead, clearly labelled.
How to use this when buying
First find the appliance’s demand and duration. Then look for evidence near that load. For a fridge, the compressor cycles; for a laptop, the workload and internal battery charge change. An average is useful for a budget but cannot establish starting power or continuous-output compatibility.
Where a matched test is missing, use a range and leave margin. The battery-size calculator exposes its assumptions. For small continuous loads, read why inverter overhead matters before paying for a bigger battery.
We would rather leave a missing measurement blank than fill it with a manufacturer runtime estimate presented as a test. If you have a reproducible reading, our contact page explains how to send a correction or source.
Can I compare every percentage in the table directly?
No. Different loads, voltage variants, cut-off settings and test methods affect the result. Use the conditions column and prefer measurements taken at a load similar to the one you plan to run.
Is a calculated runtime a published test?
No. A calculation is a planning estimate. We label it separately from a reviewer’s measured output and a manufacturer’s claim, and retain the source and conditions for each.
Correction, 16 November 2026: Flagged generation inconsistencies in the OutdoorGearLab Anker and DJI entries. Added the load-specific BLUETTI result from Smartzone.